MEO Exams

Posts

Showing posts with the label MET/2023/MAR

MET MEO Class 2 Written Question (MAR 2023)

EXAMINATION OF MARINE ENGINEER OFFICER MARINE ELECTRO – TECHNOLOGY M.E.O. CLASS II Time: 3 HOURS Total Marks - 100 Q1. What is a marine high voltage system? Sketch and describe a shipboard high voltage switch board and its protective devices. Q2 . What is soft starting of an Induction motor? Describe with a circuit using thyristors used for soft starting. Discuss its advantages and dis-advantages. Q3 . Differentiate between half and full wave rectification. State where half wave rectification may be used and the purpose for which it is not well adapted. Sketch a bridge connection by which full wave rectification may be obtained. Q4 . A. Describe with the aid of a simple sketch the arrangement of the three-phase winding of an alternator showing the neutral point. B. Explain why for most ships the neutral point is insulated. C. Explain why in some installation the neutral...

A. Which of the following three motors has the poorest speed regulation: shunt motor, series Motor or cumulative compound motor? Explain. B. A 440V shunt motor takes an armature current of 30A at 700 rev/min. The armature resistance is 0.7ohm. If the flux is suddenly reduced by 20 per cent, to what value will the armature current rise momentarily? Assuming unchanged resisting torque to motion, what will be the new steady values of speed and armature current? Sketch graphs showing armature current and speed as functions of time during the transition from initial to final, steady-state conditions.

A. Explain the working principal of a 3 phase induction motor. What are the various types of rotors? B. An 18.65Kw, 6-pole, 50Hz, 3 phase slip ring induction motor runs at 960 rpm on full load with a rotor current per phase of 35A, allowing 1Kw for mechanical losses, find the resistance per phase of 3- phase rotor winding.

A. Describe the effect of the following loads on power factor: - (i) Induction motors; (ii) Transformers; (iii) Partly loaded motors; (iv) Cage type motors. B. In a 50-Kav, star-connected, 440-V, 3-phase, 50-Hz alternator, the effective armature resistance is 0.25 ohm per phase. The synchronous reactance is 3.2 ohm per phase and leakage reactance is 0.5 ohm phase. Determine at rated load and unity power factor: (a) Internal e.m.f Ea (b) no-load e.m.f E0 (c) percentage regulation on full-load (d) value of synchronous reactance which replaces armature reaction.

Explain the effect of reduced voltage on standard cage motors with respect to EACH of the following: (i) Burn out; (ii) Starting current; (iii) Starting torque; (iv) Speed.

A. Describe with the aid of a simple sketch the arrangement of the three-phase winding of an alternator showing the neutral point. B. Explain why for most ships the neutral point is insulated. C. Explain why in some installation the neutral point is earthed?

Differentiate between half and full wave rectification. State where half wave rectification may be used and the purpose for which it is not well adapted. Sketch a bridge connection by which full wave rectification may be obtained.

What is soft starting of an Induction motor? Describe with a circuit using thyristors used for soft starting. Discuss its advantages and dis-advantages.

What is a marine high voltage system? Sketch and describe a shipboard high voltage switch board and its protective devices.

A. Why is it important to maintain high efficiency of operation and low values of voltages regulation for power transformers? B. A 100 KVA transformer has 400 turns on the primary and 80 turns on the secondary. The primary and secondary resistances are 0.3 ΩΩ and 0.01 ΩΩ respectively, and the corresponding leakage reactance’s are 1.1 ΩΩ and 0.035 ΩΩ respectively. The supply voltage is 2200 V. Calculate: (i) The equivalent impedance referred to the primary circuit; (ii) The voltage regulation and secondary terminal voltage for full load having a power factor of (a) 0.8 lagging and (b) 0.8 leading.

A. By means of a schematic circuit diagram illustrate the peak rectifier. If the supply voltage is v(t) = Vm Sin wt, what is the voltage across the load resistor? B. A battery-charging circuit is shown below in Fig. The forward resistance of the diode can be considered negligible and the reverse resistance infinite. The internal resistance of the battery is negligible. Calculate the necessary value of the variable resistance R so that the battery charging current is 1.0 A.